Home > Brother Dcp > Brother Dcp-130c Error Code 4f

Brother Dcp-130c Error Code 4f


KEVIN FLORES 404,559 views 12:37 Brother Printer J 125 w Unable To init 50 - Duration: 20:04. use the +/UP arrow button repeatedly until it says “2” then press SET 9. The printer head is always clog. DCP 130C... his comment is here

This worked for me! If this is the case then I suggest to buy a new printer rather than replace print head. Bob Newman Jayson Reymundodia April 29, 2014 at 5:37 am (UTC 0) Reply i have a brother MFC - J220 appearing error ( ink absorber full ) i just followed your I have a Brother MFC5480CN and your instructions still worked for me.

Brother Dcp 130c Erreur 4f

I found it necessary to remove the arm and gear off the shaft and then clean all parts thoroughly in order to get a lasting fix ( just using an aerosol Aditya October 30, 2013 at 2:27 am (UTC 0) Reply I have a j140 w machine, after following these steps the purge turned to 0000 but the error is still coming nazira July 6, 2015 at 6:43 pm (UTC 0) Reply I have a brother dcp 340 cw and I have followed all the steps several times but it still comes up Anyway, I now have a working printer, so many thanks.

Regards by guybagnall on Nov 9, 2011 at 9:40am Add comment Please sign in to comment 0 How to reset brother dcp135c?? I know some brand like Epson Printer it has a print limit counter. This should put you in the maintenance mode menu. Cartouche Brother Dcp 130c I cannot turn the printer off with any button.

I retried the same the thing . Brother Dcp 130c Impression Impossible 4f How can I fix a print error 4f. Just use the arrow keys instead of the numerical pad to type in numbers. erro message is "unable to init 50" and "error 46" please tell me how can i solve it.

There is an error appearing on my printer UNABLE TO CLEAN by snowy on Apr 25, 2010 at 8:25pm Add comment Please sign in to comment 0 help naman po, pano Pilote Brother Dcp 130c Could anyone help me ? by unknown on May 24, 2010 at 11:18am Add comment Please sign in to comment 0 THANK YOU!!!! Thanks!Regards,M Respond to this 0 Access the internal maintenance mode by pressing the Menu/Set button, then press * 2 8 6 4 within 2 seconds.

Brother Dcp 130c Impression Impossible 4f

Troy September 5, 2013 at 3:45 am (UTC 0) Reply I have a MFC DCP-330c could you help me thanks Troy September 5, 2013 at 3:47 am (UTC 0) Reply Could I followed the intsruction. Brother Dcp 130c Erreur 4f All-Star: An expert that got 10 achievements. Brother Dcp 130c Treiber Privacy Policy Terms of Use Sign Up Login Add Question unknown asked May 18, 2010 at 2:21pm 0 Brother DCP 130C brother dcp-130c 4f pls help how can i get out

I have tried to purge but this did not remove the message. this content by Anonymous on Oct 3, 2008 at 12:35pm Add comment Please sign in to comment 0 Ok, I keep getting the "Unable to Print see Maintainace and Troubleshooting Guide" message. by whintampz on Aug 14, 2011 at 7:47pm Add comment Please sign in to comment Hi - I have cleaned the ink pads, both, reset purge and flush to zero and by DIYprinting on Jan 22, 2013 at 12:14pm Add comment Please sign in to comment 0 I've got a Brother DCP-330C with an 'Unable to print 4F' errorI tried the maintenance Imprimante Brother Dcp 130c

thank you.. Scan head goes out fine, but on the way back, the motor doesn't stop when it reaches the back of the printer. Using the up/down and SET/OK keys enter 9 and then 9 again to exit maintenance mode. weblink I couldn't follow your instruction on my menu settings.

always got gaps in the printed blocks... Brother Dcp 130c Sterowniki any help would be grateful. Good Luck!

MVP: An expert that got 5 achievements.

Care is needed in maintenance mode, otherwise critical settings may be inadvertently corrupted.FAX models with numerical keypads: Press the Menu/Set, *, 2, 8, 6 and 4 keys within two seconds. (if It lies in a recess, adjacent and to the left of the roller, down in the back. This is the Brother definition of error code 4F: "The head drive voltage has dropped from the high to low level in an abnormally short period." or "The head drive voltage Driver Brother Dcp 130c Loading...Oops :Please try again.

Just tried your method and it worked 1st. I have bookmarked your site for ink requirements. by unknown on Aug 18, 2010 at 3:03am Add comment Please sign in to comment 1 Need help about my Brother DCP 130C printer. http://hammerofcode.com/brother-dcp/brother-dcp-130c-error-51.php I did the same procedure 10 times without success.

best wishes and thank you for your time. YOU SERIOUSLY SAVED MY LIFE, ANONYMOUS! Not a very complicated task, I eventually got everything clean even the (2) sponge containers which were pretty full. Can anyone help me?

If i reset the purge counter will it resets the toital print count? He has worked with computers and printers all of his working life and has in-depth technical knowledge on a variety of subjects. 222 comments sidhir October 18, 2012 at 7:11 am Sign in to report inappropriate content. An “initial purge”, for example, advances the purge counter by 187 + 420 = 607.

I take out the machine from the power cable and put it on again and still the message apears!!!! Sign in 3 0 Don't like this video? I have DCP-117C and error code 46. kepp flashing and its telling me cannot detect magenta ink renstall slowly can some one helps me pls tks Wcharles August 6, 2014 at 11:32 pm (UTC 0) Reply Works great