Home > Brother Mfc > Brother Mfc 8460n Fuser Error

Brother Mfc 8460n Fuser Error

Contents

Had to use a HP LaserJet 6L XP driver as there are no XP drivers for this ancient Mita. Question about Brother MFC Printers & Copiers 2 Answers How do i reset fuser kit for brother DCP 9040 CN reset fuser kit for brother DCP 9040 CN replaced fuser but The printer then needs to be told that the Fuser has been replaced, and I found out how to do this here. Explanation: Switch the fax machine off and back on again. weblink

Explanation: Switch the machine off and back on again. Explanation: Switch the machine off and back on again. Once done press 9,9 to exit Maintenance Mode and reset the machine. The service manual advices to check the environment and make sure it is not too hot.

Brother Mfc 8460n Fuser Reset

The only other thing you can do is a ( 7,7 ) which will print off a usage report that shows all sorts of interesting information. by rpauker on Aug 16, 2010 at 12:41am Add comment Please sign in to comment 0 How do i reset fuser count after replacement by Tigin on Aug 29, 2010 at Laser units tend to last well past 100,00 prints.

Hold the knobs on the rear chute assembly and pull down this to your side. 2. What to do: Machine Error: 88 Error Code: Paper Jam Error: The machine has detected a paper jam in its feed path. On these most the time once the error is given it needs to be put in service mode before the error will clear or sometimes holding the go button down while Brother Mfc 8460n Drum But the one on the same side as the gear seems essesntial - because after removing that one, it came apart and now my copier doesn't work again!

What to do: Machine Error: 8A Error Code: Printhead Error: The machine has detected a problem with the thermal head that is used to print the information on the recording paper. Brother Mfc 8460n No Paper Error Explanation: Switch the machine off and back on again. Should just pull out and right. 2. or its affiliates.

It seemed fair to assume these were the heater terminals… Having pulled off the two spade connectors, I measured the resistance and they were open circuit. Brother Mfc 8460n Scan To Pdf What to do: Error Code: B9 Error Code: Scanning Light Error: When a document is being scanned the machine detects a problem with the scanner unit light. Explanation: An engineer will be required to replace the faulty purge unit. Unlike HP machines were you usually have to just pull a cover off and unclip the fuser.

Brother Mfc 8460n No Paper Error

If nothing is found, then there may be a problem with the paper sensors. If error persists then the toner sensor may be faulty. Brother Mfc 8460n Fuser Reset Inloggen Delen Meer Rapporteren Wil je een melding indienen over de video? Brother Mfc 8460n Manual What to do: Error: 74 Error Code: Toner Error: The machine is detecting that it is out of toner.

Once the replace fuser message is displayed on the control panel the fusing assembly needs to be replaced. have a peek at these guys by Mergatroid on Apr 18, 2011 at 12:24pm Add comment Please sign in to comment 0 Hi yes I have the very same same problem with a Brother MFC 8840.It started Explanation: Check to see if the document is skidding in the document feed path, or if there is anything blocking the path. What to do: Machine Error: 8303 Error Code: Recording Paper Jam: The recording paper sensors are detecting paper in the paper path. Brother Mfc 8460n Toner

What to do: Machine Error: 78 Error Code: Heater thermistor error: The heater thermistor controls the temperature of the fuser unit and the machine is detecting a problem with this. Take a good look at the orientation of the gear and bushings that you'll have to reinstall later. If error persists the printer unit will need cleaning out and the contacts checked. check over here Keep holding button until you see maintenance on ...

What to do: Error: 57 Error Code: Duplex Error: An error has been detected while printing a double sided document. Brother Mfc 8460n Default Admin Password I know that they would be gears but if there not the gears in the fuser then what is it? What to do: Machine Error: DF Error Code: Modem Error: The modem is the device used to communicate with other fax machines.

How to fix this?

Check feeder path for obstructions and remove any foreign materials. All the time people tell me a press the menu and the * key and the display says this and that. Use 2nd/3rd party supplies at you own risk. Brother Mfc 8460n Troubleshooting Interestingly, I do not get any thumping or cracking noises on startup.

Took off the left cover, and I could rotate a gear so that a small thingy rotated and I could fit the cartridge back in. These machines take a little bit more time and effort to replace the parts. The printer has detected that there is a problem with the temperature, too hot or not heating up enough. this content First time coming across this and can't figure out the reset code to reset life counter on the fuser.

emcrae7 says: June 18, 2016 at 7:13 amI do not agree. This blog is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking If error persists then the rollers and seperation pad may need changing. If the error code persists the laser unit will need replacing.

Required fields are marked *Comment Name * Email * Website Post navigation Previous Previous post: Shuttle PN15 Wireless not installed/detected on UbuntuNext Next post: NVIDIA 3D Vision Pro and VESA Stereo Laden... Kevin Find well displayed printer parts diagrams at: http://www.printerworks.com/ <img src="http://wms.assoc-amazon.com/20070822/US/img/noscript.gif?tag=forwaypricopa-20″ alt="" /><br /><br />

Related posts:Brother MFC 8860, 8460, 8660, DCP 8065, 8060 Replace Fuser Message Brother MFC The halves will pivot on pins on the other side, then fall apart.

I got the cartridge/drum out, but couldn't get it back in. If the error persists an engineer will be required to do more in-depth cleaning. Gepubliceerd op 27 jun. 2012Instructions on how to reset and replace the fuser on a Brother MFC 8480 and 8890. THANKS!

If the error persists then the fuser will need replacing. What to do: Error Code: 50 Error Code: Replace Drum Unit: The drum unit has printed the specified number of pages for its life cycle. If the error persists try turning on the printer without the toner unit in it and see if the motor now turns. It is saying that the time taken to scan the document is excessive.

What to do: Error Code: 52 Error Code: Replace Tray 1 Feed Kit: The feed rollers and retard pad for the main paper tray have reached the end of their specified Explanation: Switch the machine off and back on again.