Home > Canon Error > Canon Error 343

Canon Error 343

Sroll from the menu option until you come to " counter ", then press OK.5. Cause: The transmitter disconnected the line during phase 3 or unable to detect the signal from the transmitter. PS3 ERROR CODE 8002A203? A. have a peek at these guys

Solution: Adjust the NL equalizer so that the other party can receive the picture or EOL signals properly. Solution: Relax the RTN transmission conditions to prevent RTN transmission. A. Cause: Abnormal protocol.

Solution: Increase #2 MENU No. 07 transmission level within a range of -8 to -15 dBm, or set #1 SSSW SW28 bit 0 to 1 to inhibit the V.8/ V.34 protocol The email address entered is already associated to an account.Login to post Please use English characters only. press [copy] and then # 3. Cause: Backup battery trouble.

A. Solution: Boost the transmission level so that the other party can receive picture or EOL signals properly. Solution: Replace SCNT PWB Solution: Replace the modem or modem attached circuit board. ##271 [ RX ] Detected 1650 Hz binary signal after CFR transmission however, failed to receive Cause: Unknown Solution: This is an error code to test for memory trouble for the L770 series.

Cause: Cannot receive the Phase signal from the other party properly due to poor line conditions. Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts Solution: Boost the transmission level so that the other party can receive the signals properly. Solution: Have the other party boost the transmission level to receive signals properly. ##705 [ TX ] Receive DCN after NACK signal detection during ARQ reception.

Solution: Press Start button after confirming the first DIS from the other party during a manual call. Cause: Line noise. Note: if the capacity of the absorption pad is unclear, register a value corresponding to the quantity of absorbed ink in pad Solution: Replace the PCNT PWB, and register a Cause: Malfunction caused by echo Solution: Take echo counter-measures as described in Service manual.

A. Cause: The other party's line was released. A. Cause: The home position sensor stays ON or OFF.

A. http://hammerofcode.com/canon-error/canon-error-020.php Solution: Have the other party boost the transmission level to receive the picture signals properly. A. Solution: Power cycle the machine (unplug unit).

A. A. Solution: Replace the board containing the Thermistor ##347 [ TX / RX ] BJ printer control ROM/ RAM check error. check my blog What am I doing wrong?

Credentials confirmed by a Fortune 500 verification firm. Solution: Make a copy of the document with a copier and then retransmit. Need to install.

Solution: Power cycle the machine. ##309 [ TX / RX ] Command error between SCPU and MCPU.

B. Solution: Replace the SCNT PWB ##261 [ TX / RX ] System error between modem and SCNT. Cause: Defective DTMF IC; (does not go into ready mode). Cause: No response to bell tone after talk reservation.

Cause: Abnormal protocol. Cause: The operation of the UPI to control the OPT2 did not finish properly. Solution: Lower the transmission start speed to 4800 bps. http://hammerofcode.com/canon-error/canon-error-05-fix.php C.

Trending Now Laura Prepon Marissa Mayer Dove Cameron Bass Pro Shop 2016 Crossovers iPhone 7 Harry Potter Car Insurance Heidi Klum Gary Johnson Answers Best Answer: This is what it means. Cause: The operation of the UPI to control the PRINT operations did not finish properly. A. Solution: Replace the board containing the BJ controller.

A. Cause: Other party cannot receive signal properly due to poor line conditions. Cause: CPU malfunction due to noise. Solution: Lengthen the no-sound time after receiving CFR so the other party can receive picture signals properly.

Cause: (Q signal transmission after picture signals); The other party cannot receive picture or Q signals properly due to poor line conditions. Solution: Divide the job so that less than 31 document are sent at one time. I don't mind if a bit of ink spills over, I would just like to get a bit more life out of the machine. B.

MFC-J615w 10/6/2016 10/6/2016 Viet - Printer Tech I have a new canon mb2020 and my imac will not recognize it 10/6/2016 10/6/2016 Viet - Printer Tech Printer laser Jet Pro 200