Canon Error 345
Cause: Printer control DRAM malfunction Solution: Power cycle the machine. Cause: Line noise. at least MINE did xD If you have no idea what youre doing, then donīt do it. Cause: Stop button was pressed during communication Solution: Retransmit ##287 [ TX ] DCN reception after MPS transmission. have a peek at these guys
Solution: Have the other party lower their transmission speed to 4800 bps. A. Cause: Cannot receive ACK properly due to poor line conditions. Solution: Retransmit.
Solution: Boost the transmission level so the other party can receive REJ properly. replied7 years ago. A. Cause: Image memory backup secondary battery is dead.
Solution: Have the other party boost the transmission level to receive picture signals properly. ##612 [ RX ] Fail to detect picture signals for 5 seconds after CFR transmission during Cause: Document is not set upon polling transmission. Solution: Adjust the NL equalizer so the other party can receive the phase signal properly. ##002 [ RX ] Picture memory full upon G2 reception. Solution: Adjust the NL equalizer so picture signals can properly be received.
Solution: Boost the transmission level so the other party can receive picture signals properly. Cause: The ink detection waste ink tank is full. Cause: Picture signal was not received properly due to poor line conditions. Solution: Install another BJ cartridge.
A. Cause: Loose carriage belt Solution: Replace carriage belt. Cause: Defective internal unit; (the wait signal will not go off for 3 seconds when waiting to respond to the reader after pre-scanning the document length). C.
Solution: Replace the ROM (U.K. Cause: The other party cannot receive the signals properly due to low transmission level. It is part of the gears you see there. Cause: Exchanger malfunction.
Try to keep the rod in line so as not to put undue strain on the toothed drive belt or the position locating film ribbon. http://hammerofcode.com/canon-error/canon-error-020.php Oh yeah, its 1 month out of warranty ! Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##738 [ RX ] Wrong block number during ARQ reception. Solution: Press Start button after confirming the first DIS from the other party during a manual call.
D. Je kunt deze voorkeur hieronder wijzigen. Solution: Replace the BJ cartridge B. check my blog Solution: No solution as modem speed is dependant on each machines specifications.
Cause: The other party cannot receive RR properly due to poor line conditions. A. Cause: Cannot receive picture signals properly due to poor line conditions.
Cause: Thermal head trouble Solution: Replace the Thermal head B. Cause: Picture signal cannot be received over 1 second due to poor line conditions. Cause: Transmission was reserved from the other party, however, your machine was out of paper. DANGER - Duur: 4:42.
Solution: Turn off the power and unplug the unit. Solution: Remove the foreign material in the carriage unit. Solution: Add a long pause after the telephone number when registering the user in the auto- dialing directory so that the system will not respond to the first DIS from the http://hammerofcode.com/canon-error/canon-error-05-fix.php Question about MultiPASS MP370 All-In-One InkJet Printer 1 Answer Error ##345 ...canon have error ##345 .
Cause: (TX / RX) The modem transmission speed is different from other machine. So perhaps cleaning out the purge unit will help. Solution: Press the START button after confirming the first DIS from the other party during a manual call. Laden...
On other Canon the actuater is too the right within the purge unit. Cause: The user telephone number is not registered (if the receiver is a Ricoh 3000L) Solution: Register user telephone number. Solution: Relax the RTN transmission conditions to prevent RTN transmission. I am French.
Solution: Check each part of the document transport unit for any abnormalities using the Service manual. ##121 [ RX ] Ink sheet and Recording paper cling together. Weergavewachtrij Wachtrij __count__/__total__ Canon MP780 printer wrong cartridge error fix. A.