Home > Canon Printer > Canon Printer Error 343

Canon Printer Error 343

Contents

Solution: Press the START button after confirming the first DIS from the other party during a manual call. Follow these steps below to reset it: 1. Solution: Adjust the NL equalizer so the other party can receive picture or Q signals properly. Cause: Thermal head trouble. news

Solution: No solution as modem speed is dependant on each machines specifications. Solution: Contact the telephone company and request line maintenance. ##010 [ RX ] Failed Phase synchronization on first sheet during reception in G2 or MF1. Cause: Picture signal was not received properly due to poor line conditions. Cause: Proper EOL signal at the start of the picture signal was not received due to poor line conditions.

Canon Printer Error Code

A. A. Cause: Defective memory. Good evening.

Cause: The other party cannot receive RTN or PIN due to poor line conditions Solution: Boost transmission level so other party can receive RTN or PIN properly. Solution: Resend Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##205 [ TX ] Data error during image memory Solution: Have the other party boost their transmission level to receive REJ properly. ##715 [ TX ] Receive signals other than RR, RNR or REJ after retransmission procedures during ARQ Canon Printer Error Code 5011 A.

Solution: Press Start button after confirming the first DIS from the other party during a manual call. Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##226 [ TX / RX ] Stack pointer not within RAM range. Solution: Adjust the NL equalizer so the other party can receive TCF properly Solution: Take echo counter-measures as described in Service manual. Solution: Refer to Service manual ##321 [ RX ] Printer (LBP) status error.

I tried and it worked.http://www.fixyourownprinter.com/forums/inkjet/29693 by Maria1 on Aug 19, 2007 at 6:25pm Add comment Please sign in to comment 0 Here is a link of a picture of the printer Canon Printer Error Code 6000 Respond to this 0 You should look at the Canon MPC ink tank full thread..I'm pretty sure that's what your problem is and you are not alone. Cause: The other party cannot receive REJ properly due to poor line conditions. Cause: Abnormal protocol.

Canon Printer Error Code 5100

B. Solution: Boost the transmission level so the other party can receive picture or MPS signals properly. Canon Printer Error Code Cause: Other party's machine is out of paper. Canon Printer Error Code B200 I'm in the middle of photocopying a large case that has to be finished tomorrow.

Cause: Abnormal protocol. http://hammerofcode.com/canon-printer/canon-printer-error-05.php Select "[4] EEPROM CLEAR"5. Cause: CPU malfunction due to noise. Cause: The other party experienced echo malfunction. Canon Printer Error Code 300

A. Number 15 is Aditional Functions.http://sites.google.com/site/customersite/mp/mp390.JPG?attredirects=01. Communication was interrupted as a preventative measure since there was a mechanical abnormality in the document transport unit. http://hammerofcode.com/canon-printer/canon-printer-dep-error.php B.

Solution: Power cycle the machine (unplug unit). Canon Printer Error Code 5200 A. Solution: Check each part of the document transport unit for any abnormalities using the Service manual. ##121 [ RX ] Ink sheet and Recording paper cling together.

Cause: Defective internal unit; (RECORD will not go on during memory copy).

Solution: Perform echo counter-measures listed in service manual Solution: Lower the transmission level to prevent echo reception of the transmitted CFR signal. ##294 [ RX ] Fail to receive Solution: Adjust the NL equalizer so the other party can receive MCF2 or PIS signals properly. ##004 [ RX ] Fail EOM/ PIS reception during G2 reception. Solution: EEPROM data are automatically initialized when this error occurs. Canon Printer Error Code U052 Normally I'd be able to refer you to an online service manual for the printer, but there doesn't appear to be one available for the MPC400.

Solution: Press Start button after confirming the first DIS from the other party during a manual call. Cause: Line noise. Solution: Boost the transmission level so the other party can receive REJ properly. http://hammerofcode.com/canon-printer/canon-printer-error-e30.php Solution: Refer to Service Manual. ##302 [ TX ] Interface error between reader and controller.

G. A. Solution: Press Start button after confirming the first DIS from the other party during a manual call. C.

A. Solution: Refer to Service manual ##311 [ RX ] Control error. Solution: Lower the transmission level to prevent reception of the transmitted CRF echo. ##265 [ TX / RX ] SCNT hardware signal error. Cause: Picture signal or RR was not properly transmitted due to poor line conditions.

Solution: Boost the transmission level so that the other party can receive carrier signals properly. Cause: The home position sensor stays ON or OFF. B. by unknown on Apr 2, 2014 at 5:04pm Add comment Please sign in to comment 0 Hi,The picture for Scan, Copy and Menu buttons:http://fix-your-printer.blogspot.com by Jann31 on Apr 8, 2014 at

Solution: Have the other party lower the reception level to prevent the other party from receiving echo signals. ##105 [ RX ] Over 40 continuous lines of data error during Cause: Other party cannot receive; (out of recording paper or not set). Solution: Have the other party lower their transmission start speed to 4800 bps Solution: Adjust the NL equalizer so that the picture signal can properly be received. ##106 [ Cause: Defective internal unit.

A. A. Select "[8] ETC.." 4. A.

Solution: Lower the transmission level to prevent the reception of echo signals. ##108 [ TX ] Detect polarity inversion during TX in f-networks 2.