Home > Error Code > Boost System Error Code 89

Boost System Error Code 89

Contents

Copyright Rene Rivera 2004-2008. Engine 3113 Main Relay 1 (High Pressure Pump -power supply to the fuel metering unit) -Short to Battery Engine 3114 Main Relay 1 (High Pressure Pump -power supply to the fuel The workaround is to place the // "throws" function in namespace boost rather than namespace boost::system. } // namespace system namespace detail { inline system::error_code * throws() { return 0; } Macro: int EMFILE The current process has too many files open and can’t open any more. have a peek here

When you call aio_cancel, the normal result is for the operations affected to complete with this error; see Cancel AIO Operations. Which architecture are you using? Trans 2346 Clutch 5-6 solenoid open circuit or short to ground. No new replies allowed.

Boost System Error Code Example

Hitch 1027 Not implemented Hitch 1028 Travel Range potentiometer value received from CAN data bus indicates failure condition. Macro: int EROFS An attempt was made to modify something on a read-only file system. TMF 11 Communications Lost with Data Bus and ALL other controllers TMF 12 Communication lost with the armrest controller TMF 14 5 Volt Sensor Supply voltage is too high TMF 15

If you've set up the env for intel64, you should use "address-model=64". The values are always the same, on every operating system. Trans 2009 Seat switch open circuit Trans 2010 Seat switch is shorted to the supply voltage B+ or 5 volt reference Trans 2011 Clutch Pot Open Circuit or short to ground Trane Error Code 89 Hitch 1037 The ARU reports EDC Inching Down switch faulty or not available.

Macro: int EUSERS The file quota system is confused because there are too many users. Boost Error Code To String Hitch 1016 Not implemented Hitch 1017 Position Command value received over the CAN data bus from the Armrest indicates Position Command potentiometer failed. XHTML 1.0 CSS OSI Certified Boost C++ Libraries ...one of the most highly regarded and expertly designed C++ library projects in the world. — Herb Sutter and Andrei Alexandrescu, C++ Coding This error never occurs on GNU/Hurd systems.

Trying the same operation again will block until some external condition makes it possible to read, write, or connect (whatever the operation). Chevrolet Error Code 89 ENG 2117 Engine Coolant Level is low. What is the syntax for using icl to compile a simple file? You signed in with another tab or window.

Boost Error Code To String

Hitch 1006 EDC Low Side Driver stuck on failure. Trans 2345 Clutch C3-4 solenoid open circuit or short to ground. Boost System Error Code Example You can choose to have functions resume after a signal that is handled, rather than failing with EINTR; see Interrupted Primitives. Boost Error Code 2048 Does that help? –John P May 28 at 17:30 add a comment| up vote 1 down vote Are you using boost::system?

TMF 163 PTO Shaft rotation is detected when the PTO clutch is OFF. navigate here Engine 3009 Coolant Temperature Sensor -(via CAN) No Signal Engine 3010 Air Intake Temperature Sensor -Signal Above Range Max. Jennifer Top Log in to post comments Judith Ward (Intel) Fri, 07/11/2014 - 12:42   Hopefully you don't need this info but the way you compile a file on the command Macro: int ENOTCONN The socket is not connected to anything. Boost Error Code 67

Hitch 1013 No communication with the ICP (Instrument Cluster Panel). Engine 3126 Hand Throttle -Channel 1 Signal Above Range Max. Macro: int ENOEXEC Invalid executable file format. Check This Out ENG 758 Rear Bank injector is bad ENG 951 A power imbalance between the cylinders was detected by the controller hardware ENG 983 Unused A/D input channel out of range.

Thanks! Boost System Error_code rename can cause this error if the file being renamed already has as many links as it can take (see Renaming Files). The system tried to use the device represented by a file you specified, and it couldn’t find the device.

Trans 2355 C3-4 Clutch Solenoid is shorted to +12 Volts, Current sensed while driver is off.

Fri, 07/11/2014 - 12:43 Hello Jennifer, Yes I did step 2. TMF 130 Aux 2nd Raise solenoid failed open or short circuit. Boost.Asio help with concurrency. Boost Error Code Waiting for client connection...", false); } I do know this code has major flaws and that it would certainly cause a lot of exceptions if it compiled.

Portability Note: In many older Unix systems, this condition was indicated by EWOULDBLOCK, which was a distinct error code different from EAGAIN. Engine 3016 Fuel Temperature Signal -Signal Below Range Min. Sorry I am a bit of a newbie here. this contact form TMF 172 PTO Solenoid Circuit is failed shorted to 12 Volts when PTO is in the off state.

The error codes are all defined in an enumeration, but most of them are assigned values from existing macros, e.g. Personal Open source Business Explore Sign up Sign in Pricing Blog Support Search GitHub This repository Watch 198 Star 1,408 Fork 502 zaphoyd/websocketpp Code Issues 108 Pull requests 24 Projects This particular implementation doesn't // produce warnings or errors from popular compilers, is very efficient // (as determined by inspecting generated code), and does not suffer // from order of initialization Copyright Rene Rivera 2004-2008.

Macro: int ENOPROTOOPT You specified a socket option that doesn’t make sense for the particular protocol being used by the socket. Macro: int EPROCLIM This means that the per-user limit on new process would be exceeded by an attempted fork. Trans 2348 110 Clutch Mid Range solenoid open circuit or short to ground. From the "dir" you're trying to call "iclvars.bat", you're trying to build for intel64.

Note that you'll have to do a little digging on linux as the actual codes are stored in a more obscure file, such as /usr/include/asm-generic/errno.h –Gearoid Murphy Oct 17 '10 at Trans 2358 Mid Clutch Solenoid is shorted to +12 Volts, Current sensed while driver is off. What i really want to know is: How can i have these threads doing the write and read operations and accessing the vector without damaging the data or causing undefined behavior? See Creating a Socket.

No ideas what caused the error 22.