Home > Error Code > Bosch Error Code E 04

Bosch Error Code E 04

Contents

Lots of other fun stuff down there too, just like yours.

We had called the repair guy and given a date two weeks from now for them to come out and look The best written, most helpful E04 error fix I have been able to find.Thank You. I've never had the e:04 on it after using about 1 tablespoon of detergent, maybe 2 for a big load. June 14, 2016 at 8:19 PM Anonymous said... this contact form

Was my last day at a rental was doing last wash and this happened. There is an side of the trap that is marked that it needs to be installed facing downward, so watch for that when you put it back in. Bosch was offering a $100 rebate on the washer. Cause: Short or break causing incorrect resistance in winding of the circulation pump or the motor.

Bosch Dishwasher Error Code E04

We twisted very hard. LG Washing Machine Error Codes Error Codes for LG Tromm Washing Machines; How to Reset Error Codes in an LG Washer; Comments You May Also Like. ...... This information was just the trick. If after listening to the podcast and applying the wisdom explained therein the problem still persists, then the only thing left is to replace the drain pump.

But water still leaking from the front. Then it made a good non-sharp tool to push against the latch. Fault code A or B Cause: Fault with the water sensor. Bosch Nexxt 500 Series Washer Service Manual How to Reset Washing Machines How to Reset Washing Machines.

Please hurry im going to bed soon. Bosch Nexxt 500 Series Washer Error Code E02 You can tape over the edge while you are working or wear gloves. We always try to use it but I guess one slipped by us and the rubber boot - and right into the trap before the pump. This trickle quickly increases, so go SLOW, with the vac running the whole time.

I have not seen your model. Bosch Nexxt 500 Series Washer Won't Drain You can twist this cap off by hand and remove all the debris inside. First, the error. Followed the instructions again, when sump was open I attempted to turn the white "button" that i assume is attached to the pump shaft to see if it was impeded.

Bosch Nexxt 500 Series Washer Error Code E02

Never been a problem! signed: Not Particularly Mechanically Inclined in Maine Michael See inside of your appliance - diagrams and part photos for virtually every model. Bosch Dishwasher Error Code E04 Go to: Why is My Dishwasher Not Heating the Water? Bosch Nexxt 500 Series Washer Error Codes E 13 Apparently that was useless, and this is the answer.

July 22, 2016 at 2:41 AM Post a Comment Newer Post Home Subscribe to: Post Comments (Atom) Blog Archive ▼ 2008 (5) ▼ May (5) My First Post is My Last http://hammerofcode.com/error-code/bosch-error-code-e13.php Why is My Dishwasher Not Drying the Dishes? Found a pedi sock stuck in there that I had "lost" a while back. Fault Code E20 Symptom: Electrical short or break. Bosch Washer Error Codes

By Model Number By Part Description By Part Number powered by AppliancePartsPros.com « bad bearing | Whirlpool Duet Sport Front Loader - Signal F21 » Thread Tools Show Printable Version We do our own cloth diapers and also weekly laundry for our local food co-op, so there's really no knowing what sort of putrid funk is hanging out in the machine's When I take the sump cover off I have no basket. navigate here Rotate the hole (clockwise) to 6'oclock and it should come free.

Action: Check motor and motor tacho wiring for problems. Bosch 500 Series Washer Troubleshooting Do not twist or you will break off the little plastic circle pieces.

Here's what it looks like

did u get an answer I have the same issue

I have the same problem. The E04 Light comes on and the unit does not drain.

I repaired my machine in less than 20 minutes. (Some sort of fabric was clogging the sump.) Please add a comment/update to step 1 to indicate the need to press in

I find it pretty easy to
replace, one hex screw driver and a pair of pliers are all that is required and
the hardest part is getting the rubber boot strap The door to that area which I unscrewed had some odd shaped parts attached to it so getting it in the proper orientation to screw back in took a minute but Fault Code F Cause: Fill timeout. Bosch Nexxt Washer Problems It is actually not uncommon for these drain pumps to fail this way.

I have tried running the machine with the hose draining into a 5 gallon bucket that is placed on the ground . Gently press on the panel with your other hand while you rotate the panel clockwise to move the hole to the 6 o'clock position. It is still not working. his comment is here Bearings wear out and starting binding randomly causing slow or no pump out problems with the resulting E:04 error code that you're seeing.

I saw the Lowe's guys open up the box, it was new from the factory, but I guess they forgot to put it in. Very sore fingers from trying to turn without first pushing in. You saved me a lot of time and frustration. You can adjust your use of detergent and reset the machine to eliminate the error code.

The washing machine will still not drain, and I still get the same error. Fault Code E14 Cause: Reed switch flow sensor fault Action: Check contacts on the reed switch connection are clean. If I am understanding you, yes, your pump is broken. At some point the threads will have backed off enough that a trickle of water will come out.

I'm not a trained service technician. How Not to Move Your Bosch Nexxt How to Open the Drain Bosch Nexxt Front Load Washer's E:04 Error skip to main | skip to sidebar Bosch Nexxt E:04 Error Thank you so much for the information. Insert a sturdy, pointed object into the hole; my favorite is an awl, though a heavy duty paperclip unwound also works.

It's almost been a year, and no phone call ;) Posted by Kevin at 4:57 PM 10 comments: Anonymous said... Error Code E27 for a Bosch Washer The door lock doesn't properly close or the door lock sensor is not sending the proper message to the washer machine controls. On the panel is a small hole. disclaimer and Terms of Use.

boschhead Dryer Repair 1 01-10-2008 07:01 PM All times are GMT -7. Hi Carl, The root of this problem is slow draining. It cause a clog in the drain pipe coming off just under the drum. The machine gets to a certain point in the cycle , drain pump does not pump,and then the error code comes up.

Errors "E02," "E03," "E04" and "E05" are thermistor errors. ... Action: Check inlet valve and water supply.